SPI Supplies Division|
|
Date Effective........... January 14, 2010
(most recent revision)
Chemical Name/Synonyms... Not known
Chemical family.......... Mixture
Emergencies
Contacting CHEMTREC 24 Hour Emergency
Use Only #'s............. Worldwide phone : 1-(703)-527-3887
Worldwide FAX : 1-(703)-741-6090
Toll-free phone : 1-(800)-424-9300
Product or Trade Name.... SPI #04988-AB, 04988-FA Pikal® Paste
Intended Use: Metal polish
CAS #.................... Mixture
Chemical Formula......... Not known
Component Name CAS # OSHA OSHA ACGIH ACGIH Carcinogenic %
PEL STEL TLV STEL
Listing
Abrasives
1344-28-1 N/L N/L N/L N/L N/L 40%
7631-86-9
Mineral Oil
64642-56-9
8008-20-6 N/L N/L N/L N/L N/L 36%
Fatty acid
112-80-1 N/L N/L N/L N/L N/L 12%
Wax
8002-74-2 N/L N/L N/L N/L N/L 12%
Emergency overview:
This material is not hazardous by OSHA Hazard Communication
Definition. This material possesses no known hazards to health.
Signal Word:
CAUTION!
Physical Health Hazards:
When wet paste dries out, dry dust might form which may form
respirable particulates if disturbed. If this material gets
into the eyes, either wet or dry, it could be irritating. Never
allow material to remain on a surface to dry out; that way the
potential hazard is eliminated. Wipers used for the polishing
should always be disposed of in an approved container. When wipers
containing the dried paste are disturbed, respirable particulates
could be formed.
Physical state: Paste
Color: Khaki
Odor: Faint
Odor threshold: No data available
Potential Health Effects:
Routes of exposure
Eye contact, ingestion, skin contact
Signs and Symptoms of Acute Exposure:
This material if used properly, should not pose any kind of
real hazard. If the material is used improperly, for example,
if applied to a hot surface, organic vapors will be given off,
and if this was done in an improperly ventilated area, an
explosion hazard could be created.
Skin contact:
Could be an irritant.
Inhalation:
Material is an irritant at high levels of exposure; can
cause headache and nausea. Consult physician.
Eye contact:
Mechanical irritation is possible; can be irritant.
Ingestion:
Ingestion is unlikely, but if it does occur, material could
be expected to be an irritant. Drink water after rinsing
out mouth first. Try to prevent vomiting.
Chronic Health Effects Summary:
No known chronic health effects.
Conditions Aggravated by Exposure:
No known conditions are aggravated by this material.
Work/Hygienic Practices:
Do not eat, drink, or smoke during work.
Carcinogenicity:
NTP: Not applicable
IARC Monographs: Not applicable
OSHA Regulated: Not applicable
Take proper precautions to ensure your own health and safety before
attempting to rescue and providing first aid. For specific information
refer to the Emergency Overview in Section of this MSDS.
Inhalation: If symptoms are experienced, move victim to fresh
air, if symptoms persist, obtain medical attention.
Eye Contact: Wash eyes with clean low-pressure water.
Continue to rinse for 15 minutes.
If irritation persists, seek medical
advice. Do not rub the eyes as this
product does contain abrasive powder
and damage to the eye will result.
Skin Contact:
Wash skin with soap and water until soapiness is removed.
If irritation persists, seek medical advice. Do not rub
the skin that contains this product since the product contains
abrasive particles which could end up causing skin damage.
Ingestion:
If product is swallowed, first rinse out mouth several
times to remove material from mouth and to keep more from
being swallowed. Water may be taken to dilute the product
already in the stomach. Seek medical advice and consult a
physician promptly.
NFPA Rating: Not known
Flammability classification:
Flammable
Flash Point/Method: 62°C (143.6°F) Pensky Martens
Auto-Ignition Temperature: Not known
Flammable Limits: Lower: Not applicable
Upper: Not applicable
Hazardous Combustion Products:
Specific Dangers: Combustion products may include carbon monoxide,
oxides of nitrogen, oxides of sulfur, and
unburned hydrocarbons.
Special Conditions to Avoid:
Dried dust particles of this product suspended in the atmosphere
can be respirable and in addition, they can also be combustible and
may be explosive. Keep away from heat, sparks, flame and all
other ignition sources. Keep container closed. Clean up dust
accumulations. Prevent dust accumulations and dust clouds,
If used according to instructions, this kind of situation should
never develop.
Extinguishing Media:
Any suitable medium for extinguishing the supporting fire. Use
water to keep fire-exposed containers cool. For fire specifically
involving this product, use dry foam, dry chemical or water spray,
CO2, sand, or earth to extinguish the fire.
Fire Fighting Instructions:
Protective Equipment/Clothing: Wear a NIOSH approved positive
pressure self-contained breathing apparatus and firefighter
turnout gear. This should be selected on the basis of the
supporting fire.
Instructions: Use flooding quantities of water until well
after fire is out.
See Sections 8 and 13. Personal precautions: Avoid contact with eyes and skin. Cleaning procedures: Wipe thoroughly with wiping cloths, for example lint-free cotton wipers. Release response: Pick up with dry cloth and retain for recycle or disposal for spills involving up to 5 liters. Do not flush spilled material to the sewer or the environment. Formation of flammable vapor/air mixtures possible. Reportable Quantities: See Section 15: Regulatory information. For larger spills: If possible, ventilate the area. The spilled material should be scooped into a suitable container for subsequent disposal. Consult local waste authority, Environmental Protection Agency, local council or an expert on advice for disposal.
Handling: Use in well ventilated areas. Wear suitable gloves if prolonged exposure is contemplated. Otherwise, less substantial gloves can be worn, such as vinyl gloves. Storage: Store away from excessive heat and away from strong oxidizing agents. Keep container tightly closed to prevent evaporation of liquid components. Store in a cool, dry, frost-free place and well out of the reach of children. The recommended temperature range for storage is between 0°C and 40°C.
Occupational Exposure Limits: Not known. Engineering Controls: Avoid contact with skin and eyes. Respiratory Protection: None necessary under normal working conditions but product should be used only in a well ventilated area. Hand Protection: PVC or rubber gloves with prolonged use. Eye Protection: Chemical resistant goggles if eye contact can accidentally occur. Skin Protection: Wear an apron or coveralls if exposure is likely to be prolonged. The product does not present a significant hazard in normal use. Data above refers to prolonged contact with large quantities of product.
External appearance: Khaki colored paste
Boiling Point/Range: 150°C (302°F)
pH: Not known
Vapor Pressure: Not known
Viscosity: Not known
Specific Gravity:
Solid/Liquid 1.1 g/ml (water = 1)
Octanol/Water Partition Coefficient in Kow: Specific value not known
Melting/Freezing Point: 53°C (127.4°F)
Evaporation Rate: Not known
Odor: Slight
Chemical Stability:
The product is stable
Conditions to Avoid:
Excessive heat; strong oxidizing agents
Incompatibility with:
Strong oxidizing agents
Hazardous Products of Deposition:
Not known. See Section 5 for combustion products.
Reactions with Air and Water:
Does not react with air, water or other common materials.
Skin contact: Low order of toxicity, frequent or prolonged contact may cause dermatitis.
Eye contact: Irritating but does not injure eye tissue unless rubbed.
Ingestion: Minimal toxicity. The viscosity of this preparation
mitigates the risk of aspiration into the respiratory
system during ingestion or vomiting.
Chronic Effects/Carcinogenicity:
None expected
Reproductive/Development Effects:
No reproductive or developmental effects are expected.
Not known, however, because of the high viscosity of this paste material, it would be highly unlikely that any would ever leak out into the environment.
Consumer Instructions: Empty tubes may be disposed of with normal
household waste.
Bulk Quantities: Dispose of in accordance with local, regional or
national requirements.
This product is not classified as dangerous.
DOT Hazard Class: Non-Regulated
UN/NA ID: Not Regulated
Packing Group: Not Applicable
Labels: Not Regulated
Marine Pollutant: No
NAER Guidebook: Not Regulated
DOT Status: Not Regulated
This preparation not classified as dangerous under The Chemical
(Hazard Information and Packaging Regulations) 1994 No.3247 or
Council Directive 88/379/EEC of 7 June 1988 relating the Classification,
Packaging and Labelling of Dangerous preparations.
The following safety phrases are appropriate:
Keep out of reach of children.
Avoid contact with skin and eyes.
If swallowed seek medical advice immediately and show this container
or label.
TSCA:
All components of this product are listed on the TSCA 8(b) inventory.
If identified components of this product are listed under the TSCA 12(b)
Export Notification Rule, they will be listed below.
TSCA 12(b) Component Listed under TSCA Section
SARA-Section 313 Emissions Reporting:
Component Reporting Threshold
SARA-Section 311/312:
No components present in this product are subject to the reporting
requirements of this statute.
CERCLA Hazardous Substances and their Reportable Quantities:
Component Reportable Quantity
California Prop. 65:
Proposition 65 requires manufacturers or distributors of consumer
products into the State of California to provide a warning statement
if the product contains ingredients for which the State has found to
cause cancer, birth defects or other reproductive harm. If this product
contains an ingredient listed by the State of California to cause cancer
or reproductive toxicity, it will be listed below:
Disclaimer of Liability: Caution! Do not use SPI Supplies products or materials in applications involving implantation within the body; direct or indirect contact with the blood pathway; contact with bone, tissue, tissue fluid, or blood; or prolonged contact with mucous membranes. Products offered by SPI Supplies are not designed or manufactured for use in implantation in the human body or in contact with internal body fluids or tissues. SPI Supplies will not provide to customers making devices for such applications any notice, certification, or information necessary for such medical device use required by US FDA (Food and Drug Administration) regulation or any other statute. SPI Supplies and Structure Probe, Inc. make no representation, promise, express warranty or implied warranty concerning the suitability of these materials for use in implantation in the human body or in contact with internal body tissues of fluids. ************************************************************************ The information and recommendations set forth above are taken from sources believed to be accurate as of the date hereof, however SPI Supplies and Structure Probe, Inc. make no warranty with respect to the accuracy of the information or the suitability of the recommendations, and assume no liability to any user thereof. The information contained in this sheet does not constitute a hazard assessment and should not be used in place of the user's own assessment of work place risks as required by other health and safety legislation. Be aware of the Structure Probe, Inc. Copyright Policy. Structure Probe, Inc. grants a nonexclusive license to make unlimited copies of this safety sheet for internal use only. Quite obviously, this information would pertain only to this material when purchased from SPI Supplies or SPI authorized agents and distributors, and in original SPI Supplies packaging, as product from other sources, with other ingredients and impurity levels could have substantially different properties.
To Ask a Question or Make a Comment
To Place an Order or Request a Quote
