|
|
Date Effective........... February 17, 2007
(most recent revision)
Chemical Name/Synonyms... Acrylic resins
Chemical family.......... Acrylic Resin Mixture
Emergencies
Contacting CHEMTREC:
24 Hour Emergency Use Only #'s......
Worldwide phone: 1-(703)-527-3887
Worldwide FAX: 1-(703)-741-6090
Toll-free phone: 1-(800)-424-9300 USA only
Product or Trade Name.... SPI #02685-AB, -AA; 02686-AB, -AA; 02687-AB, -AA Mercox® Resin
CAS #.................... Mixture (see below)
Chemical Formula......... Not known
Component Name CAS # OSHA OSHA ACGIH ACGIH Carcinogenic
PEL STEL TLV STEL
Listing
Butyl Benzyl Phthalate
85-68-7 100 ppm N/L N/L 100 ppm N/L >50%
Other methacrylic esters¹ N/L N/L N/L N/L <50%
Note: N/L = Not listed
¹ The identity of the remaining ingredients is
proprietary and no further information is known to us.
NFPA Rating: Not known at this time
Emergency overview:
This material is not hazardous by OSHA Hazard Communication
Definition
Signal Word
CAUTION!
Physical Health Hazards:
Dust may form explosive mixtures with air. Molten polymer may
cause thermal burns. Irritating fumes may be produced at process
temperatures.
Physical state: Liquid
Color: Clear, red, or blue depending on specific product number
Odor: Acrid acrylic odor
Odor threshold: No data available
Potential Health Effects:
Routes of exposure
Eye contact, ingestion, skin contact
Signs and Symptoms of Acute Exposure:
Not known
Skin contact:
Irritation (acute) can occur.
Allergic reactions may occur (chronic)
Inhalation:
At process temperatures irritating fumes may be produced.
Inhalation of process fumes may cause soreness in the nose
and throat and coughing. Inhaling polyethylene dust is
considered a nuisance.
Eye contact:
Vapor or mist irritates mucous membranes and the upper
respiratory tract.
Ingestion:
Nausea and vomiting
Chronic Health Effects Summary:
Allergic skin reactions may occur resulting in severe
dermatitis conditions.
Conditions Aggravated by Exposure:
No known conditions are aggravated by this material.
Take proper precautions to ensure your own health and safety before
attempting to rescue and providing first aid.
Inhalation: Remove victim to fresh air. If breathing is difficult,
give oxygen. If not breathing, give artificial respiration
and call physician immediately.
Eye Contact: Immediately flush eyes with plenty of water for 15 minutes.
Skin Contact: Immediately flush skin with copious amounts of water.
Ingestion: Call physician immediately.
Other: Prolonged exposure may cause narcotic effect.
NFPA Rating: Health: 0 Fire: 1 Reactivity: 0
Flammability classification:
Not classified.
Flash Point/Method: 10°C (50°F)
Auto-Ignition Temperature: 434°C (815°F)
Flammable Limits: Lower: Not applicable
Upper: Not applicable
Hazardous Combustion Products:
Toxic fumes of oxides of carbon.
Special Conditions to Avoid:
Keep away from light, heat, sparks and any other ignition sources.
Extinguishing Media:
Use dry chemicals, CO2, water spray. Use water spray to cool fire
exposed containers. Wear self-contained breathing apparatus and
protective clothing.
Fire Fighting Instructions:
Protective Equipment/Clothing: Wear a NIOSH approved positive
pressure self-contained breathing apparatus and firefighter
turnout gear.
Instructions: Use flooding quantities of water until well after
fire is out.
Release response:
Shut off all sources of ignition. Wear self contained
breathing apparatus, rubber boots and heavy rubber gloves.
Cover with an activated laboratory carbon absorbant, take
up and place in closed containers. Transport outdoors.
Ventilate are and wash spill site.
Reportable Quantities: Not known
Handling: Keep tightly closed and away from heat, sparks, open
flames and sources of ignition. Local exhaust
ventilation should be provided in work areas.
Storage: Keep container dry. Store away from excessive heat and
store refrigerated. Keep container closed to prevent
contamination.
Other: Methyl methacrylate is inhibited with 10 ppm hydroquionone
monomethyl ether. Do not store under inert atmosphere.
It is adviseable to use material within six months.
Engineering Controls: None identified.
Personal Protection:
Inhalation: NIOSH/MSHA approved protection where atmosphere exceeds
recommended limits. Use only in chemical fume hood.
Skin: Gloves, rubber.
Eye: Chemical safety goggles and shield.
Other: Safety shower and eye bath should be available.
Boiling Point/Range: 100°C (212°F)
pH: Not applicable
Vapor Pressure: 29 mm Hg at 20 °C
Vapor Density: 3.5
Viscosity: Not applicable
Specific Gravity:
Solid/Liquid 0.936 (water = 1)
Vapor Not applicable
Water solubility: Soluble
Reactivity with water: Not reactive
Evaporation Rate: Not available
Octanol/Water Partition Coefficient in Kow: Specific value not known
Melting/Freezing Point: -48°C (-54°F)
Chemical Stability: The product is unstable in the absense of inhibitor.
Conditions to Avoid: Keep away from light, heat and sparks.
Incompatibility with: Oxidizing agents, peroxides, bases, acids,
reducing agents, amines, and halogens.
Hazardous Products of Deposition: Toxic fumes of oxides of carbon.
Reactions with Air and Water: Does not react with air, water or other
common materials.
Summary: Can be absorbed through skin and severe allergic reactions
can occur.
Component:
LC50 (INHL): Not known.
Skin Effects: Severe allergic reactions can develop.
Acute Inhalation Effects: Breathing can stop.
Subchronic Effects: Not known.
Chronic Effects/Carcinogenicity: None reported.
Reproductive/Development Effects: No reproductive or developmental
effects have been reported.
Exotoxicity: No information found in our selected references. Environmental Fate: No information found in our selected references. Bioaccumulation: Not expected to occur.
Burn in chemical incinerator equipped with an after-burner scrubber. Exert extra care when igniting since this material is highly flammable.
Proper Shipping Name: Flammable liquid (methyl methacrylate, inhibited) DOT Hazard Class: UN/NA ID: UN 1247 Packing Group: Marine Pollutant: Not known NAER Guidebook: Not Regulated DOT Status: Regulated
TSCA: All components of this product are listed on the TSCA 8(b)
inventory. If identified components of this product are listed under
the TSCA 12(b) Export Notification Rule, they will be listed below.
TSCA 12(b) Component Listed under TSCA Section
SARA-Section 313 Emissions Reporting:
Component Reporting Threshold
SARA-Section 313 Title III. This product is subject to the
reporting requirements.
California Prop. 65:
Proposition 65 requires manufacturers or distributors of consumer products
into the State of California to provide a warning statement if the product
contains ingredients for which the State has found to cause cancer, birth
defects or other reproductive harm. If this product contains an ingredient
listed by the State of California to cause cancer or reproductive toxicity,
it will be listed below:
Disclaimer of Liability: Caution! Do not use SPI Supplies products or materials in applications involving implantation within the body; direct or indirect contact with the blood pathway; contact with bone, tissue, tissue fluid, or blood; or prolonged contact with mucous membranes. Products offered by SPI Supplies are not designed or manufactured for use in implantation in the human body or in contact with internal body fluids or tissues. SPI Supplies will not provide to customers making devices for such applications any notice, certification, or information necessary for such medical device use required by US FDA (Food and Drug Administration) regulation or any other statute. SPI Supplies and Structure Probe, Inc. make no representation, promise, express warranty or implied warranty concerning the suitability of these materials for use in implantation in the human body or in contact with internal body tissues of fluids.
To Ask a Question or Make a Comment
To Place an Order or Request a Quote
